In toxicology, the median lethal dose, LD₅₀ (abbreviation for "lethal dose, 50%"), LC₅₀ (lethal concentration, 50%) or LCt₅₀ is a toxic unit that measures the lethal dose of a given substance.^[1] The value of LD₅₀ for a substance is the dose required to kill half the members of a tested population after a specified test duration. LD₅₀ figures are frequently used as a general indicator of a substance's acute toxicity. A lower LD₅₀ is indicative of higher toxicity.

The term LD₅₀ is generally attributed to John William Trevan.^[2] The test was created by J. W. Trevan in 1927.^[3] The term semilethal dose is occasionally used in the same sense, in particular with translations of foreign language text, but can also refer to a sublethal dose. LD₅₀ is usually determined by tests on animals such as laboratory mice. In 2011, the U.S. Food and Drug Administration approved alternative methods to LD₅₀ for testing the cosmetic drug Botox without animal tests.^[4][5]

Conventions

The LD₅₀ is usually expressed as the mass of substance administered per unit mass of test subject, typically as milligrams of substance per kilogram of body mass, sometimes also stated as nanograms (suitable for botulinum), micrograms, or grams (suitable for paracetamol) per kilogram. Stating it this way allows the relative toxicity of different substances to be compared and normalizes for the variation in the size of the animals exposed (although toxicity does not always scale simply with body mass). For substances in the environment, such as poisonous vapors or substances in water that are toxic to fish, the concentration in the environment (per cubic metre or per litre) is used, giving a value of LC₅₀. But in this case, the exposure time is important (see below).

The choice of 50% lethality as a benchmark avoids the potential for ambiguity of making measurements in the extremes and reduces the amount of testing required. However, this also means that LD₅₀ is not the lethal dose for all subjects; some may be killed by much less, while others survive doses far higher than the LD₅₀. Measures such as "LD₁" and "LD₉₉" (dosage required to kill 1% or 99%, respectively, of the test population) are occasionally used for specific purposes.^[6]

Lethal dosage often varies depending on the method of administration; for instance, many substances are less toxic when administered orally than when intravenously administered. For this reason, LD₅₀ figures are often qualified with the mode of administration, e.g., "LD₅₀ i.v."

The related quantities LD₅₀/30 or LD₅₀/60 are used to refer to a dose that without treatment will be lethal to 50% of the population within (respectively) 30 or 60 days. These measures are used more commonly within radiation health physics, as survival beyond 60 days usually results in recovery.

A comparable measurement is LCt₅₀, which relates to lethal dosage from exposure, where C is concentration and t is time. It is often expressed in terms of mg-min/m³. ICt₅₀ is the dose that will cause incapacitation rather than death. These measures are commonly used to indicate the comparative efficacy of chemical warfare agents, and dosages are typically qualified by rates of breathing (e.g., resting = 10 L/min) for inhalation, or degree of clothing for skin penetration. The concept of Ct was first proposed by Fritz Haber and is sometimes referred to as Haber's law, which assumes that exposure to 1 minute of 100 mg/m³ is equivalent to 10 minutes of 10 mg/m³ (1 × 100 = 100, as does 10 × 10 = 100).

Some chemicals, such as hydrogen cyanide, are rapidly detoxified by the human body, and do not follow Haber's law. So, in these cases, the lethal concentration may be given simply as LC₅₀ and qualified by a duration of exposure (e.g., 10 minutes). The Material Safety Data Sheets for toxic substances frequently use this form of the term even if the substance does follow Haber's law.

For disease-causing organisms, there is also a measure known as the median infective dose and dosage. The median infective dose (ID₅₀) is the number of organisms received by a person or test animal qualified by the route of administration (e.g., 1,200 org/man per oral). Because of the difficulties in counting actual organisms in a dose, infective doses may be expressed in terms of biological assay, such as the number of LD₅₀s to some test animal. In biological warfare infective dosage is the number of infective doses per cubic metre of air times the number of minutes of exposure (e.g., ICt₅₀ is 100 medium doses - min/m³).

Limitation

As a measure of toxicity, LD₅₀ is somewhat unreliable and results may vary greatly between testing facilities due to factors such as the genetic characteristics of the sample population, animal species tested, environmental factors and mode of administration.^[7]

There can be wide variability between species as well; what is relatively safe for rats may very well be extremely toxic for humans (cf. paracetamol toxicity), and vice versa. For example, chocolate, comparatively harmless to humans, is known to be toxic to many animals. When used to test venom from venomous creatures, such as snakes, LD₅₀ results may be misleading due to the physiological differences between mice, rats, and humans. Many venomous snakes are specialized predators on mice, and their venom may be adapted specifically to incapacitate mice; and mongooses may be exceptionally resistant. While most mammals have a very similar physiology, LD₅₀ results may or may not have equal bearing upon every mammal species, such as humans, etc.

Examples

Note: Comparing substances (especially drugs) to each other by LD₅₀ can be misleading in many cases due (in part) to differences in effective dose (ED₅₀). Therefore, it is more useful to compare such substances by therapeutic index, which is simply the ratio of LD₅₀ to ED₅₀.^{[citation needed]}

The following examples are listed in reference to LD₅₀ values, in descending order, and accompanied by LC₅₀ values, {bracketed}, when appropriate.